Bose FreeSpace DXA 210 Digital Mixer/Amplifier

Bose FreeSpace DXA 210 Digital Mixer/Amplifier

The DXA 2120 digital mixer/amplifier can be used in both low- and high-impedance systems. Each of the two output channels delivers 120 watts at 4 ohms or 100 watts for 70/100-volt applications. An auxiliary output provides a linelevel signal for system expansion. The DXA 2120 digital mixer/amplifier has six inputs - four mic/line inputs, one page input and one direct input that overrides all other sources when a signal is detected. The four mic/line inputs connect to sources via 3-pin Euroblock connectors or dual RCA jacks.

Three operating modes provide greater flexibility for installed music or speech applications:
Mixer Mode - Each input can be routed to every output simultaneously. Volume for each input can be controlled independently, or a master volume can control both outputs simultaneously.
Dual Mono Select Mode - Two input sources are available for each output channel. Volume control and source selection are available in each zone.
Stereo Select Mode - Two selectable stereo sources can be played in stereo in a single output zone. Volume control and source selection are available in the zone.

The auxiliary output can be used with all three modes of operation.

Two user interfaces, volume control and volume control with A/B select, are available for operation from remote locations.

• Six inputs: four mic/line inputs with choice of balanced Euroblock or unbalanced RCA connectors, one page input and one direct input
• Two powered outputs that can operate at high or low impedance: 2 x 120 W at 4 ohms , 2 x 65 W at 8 ohms, or 2 x 100 W at 70/100V
• Three operating modes for greater flexibility in installed music or speech applications: Mixer Mode, Dual Mono Select Mode, and Stereo Select Mode
• Easy setup and control via onboard controls - no computer needed
• DSP includes loudspeaker EQs and dynamic EQ functions engineered specifically for Bose loudspeakers
• Opti-voice paging provides a smooth transition between music and announcements
• 24-volt DC backup power connection for added reliability and integration onto fire and evacuation systems

Amplifier Power
2 x 120 W at 4 ohms , 2 x 65 W at 8 ohms, or 2 x 100 W at 70/100V
Frequency Response
40 Hz - 16 kHz (+0/-3 dB)
Signal-to-Noise Ratio
75 dB (below rated power, A-weighted)
THD
<=0.5 % (at full rated power)
Channel Separation (Crosstalk)
<=-60 dBV (below rated power, 1 kHz)
Dynamic Range
80 dB
A/D and D/A Converters
24-bit
Sample Rate
44.1 kHz
Input Channels
6 channels
LED Status Indicators
Blue LED: power, Green LED: signal present, Red LED: clip
Mains Voltage
100 V version: 100 VAC; 50/60 Hz
120 V/220-240 V version: 120 V/220-240 VAC; 50/60 Hz
AC Power Consumption
Idle: 39 W, Active: 350 W
Maximum Inrush Current
23.2 A @ 230 V ~ 50 Hz
33.2 A @ 120 V ~ 60 Hz
Overload Protection
T6.3AL/250 V (100 V and 120 V) or T3.15AL/250 V (220-240 V)
DC Backup Power/Connector
+24 V (+/-1 %) Connector 2-terminal barrier strip
Input Voltage Level
+24 V
Minimum Input Power
50 W
Maximum Input Power
150 W
Dimensions
3.5" H x 16.5" W x 13.8" D (90 mm x 420 mm x 349 mm)
Net Weight
32 lb (14.4 kg)
Operating Temperature
32 °F - 104 °F (0 °C - 40 °C)
Storage Temperature
-40 °F - 158 °F (-40 °C - 70 °C)
Humidity
40 % - 90 % relative humidity
Communication Port
RS-232 serial port